Welcome to our Mining equipment manufacturing base, Contact Us


4.6 Copper slag as fine aggregate Copper slag has the high toughness so it can be used to partially replacing the fine aggregate. The proportions by weight of copper slag added to concrete mixtures were as follows 0%, 10%, 20%, 30%, 40%, 50%, 60%, 75% and . [11] Table 6. Mix ratio [2] Cement Water Fine aggregate Coarse aggregate


The effect of copper on the corrosion properties of mooring chain steel in synthetic seawater at room temperature were investigated by weight loss tests, electrochemical methods and corrosion product analysis. The results indicated that the mooringchain steel exhibited active dissolution behavior in synthetic seawater.


Corrosion problems of copper waffle coolers are experienced in Platinum Group Metals (PGM's) smelting furnaces. The copper cooler wear mechanism ... (frozen slag) formed a barrier between the copper cooler and the feed. At the bottom section of the slag zone the front refractory brick was still intact. Base metal sulphides and element sulphur ...


copper slag waste.The result of this study emphasized the effectiveness of copper slag replacement in improving the concrete resistance against sulfate attack. In this study, the sulfate resistance of concrete made with 5%, 10% and 15% of copper slag were studied in comparison with concretes without copper slag replacement.


die casting of partially solidified ferrous alloys 11/30/1979 yasİn hİlmİ dr. nacİ sevİnÇyazan die casting of partially solidified copper alloys 10/16/1979 tarik dr. m. etİ uygurbaykara investigation of the production of wc-co and wc-tic-co 12/29/1980 alper tunga dr. İlhan a. aksaydavutoĞlu determination of the work of adhesion by a


Get More Information

IOSR Journal

Series-4 (Jan. – Feb. 2021) Jan. – Feb. 2021 Issue Statistics. Abstract: The depletion of the world's fossil oil reserves and the increasing energy demand, demand to look for other energy sources. Generating electrical energy using renewable energy such as energy: water, wind, solar, and battery charging systems.


both are partially replaced by Copper slag. 3.2 Objectives 1) To study the property and characteristics of M sand and copper slag 2) Collection of primary data 3) To compare the properties and characteristics of various materials used in mix designing with IS code 4) To carry out mix design by using m sand as fine aggregate.


Portland Cement Partially Replaced by Blast Furnace Slag and Multi-Walled Carbon Nanotubes: Effect on Corrosion ... The corrosion behavior of reinforced concrete is an important factor affecting its durability. ... copper/copper sulfate and graphite electrodes were used as a working electrode, reference and counter ...


with Copper Slag (40%) and cement was partially replaced with Silica Fume from 5% to 15% at an interval of 5%. This research gives a detailed observational study on Compressive strength, split tensile strength, flexural strength at age of 28 days.


After the Copper slag blasting, dust, paint and steel dust will be settled in the dock floor and complete removal of this dust from the dock floor is not possible. This settled dust will flow into the sea during undocking of the vessel, thereby polluting the sea. D. Soil Pollution Waste copper slag after blasting is dumped openly in yard and


Jul 25, 2013· In third part, assessment of corrosion and durability studies were incorporated. Since copper slag contains more than 55% of Fe2O3 content, corrosion and durability factors are necessary to find out. in concrete. The final fourth part of this investigation, seismic application of copper slag was incorporated.


Hydrogen sulphide (H 2 S) is considered one of the most corrosive atmospheric pollutants. It is a weak, diprotic, reducing acid, readily soluble in water and dispersed into the air by winds when emitted from natural, industrial, and anthropogenic sources. It is a pollutant with a high level of toxicity impairing human health and the environment quality.


Nov 01, 2003· Air-cooled copper slag has a black colour and glassy appearance. The specific gravity varies with iron content, from a low of 2.8 to as high as 3.8. The unit weight of copper slag is somewhat higher than that of conventional aggregate. The absorption capacity of the material is typically very low (0.13%).


Aug 01, 2019· Corrosion is a serious problem for ships and o shore structures operating in seawater. ... cleaning is dry blasting, which is often carried out by spraying abrasives (such as grit) from copper slag or similar abrasives and reusable steel shots against work pieces to achieve the blasting standard [2]. ... cleaned surface are partially discussed ...


aggregate by using copper slag. However further addition of copper slag caused reduction in strength. From chemical composition of copper slag Fe2O3 present in more than 55%. So that here concrete itself getting corrode. Here corrosion inhibitors at the amount of 1%, 2% and 3% by the weight of cement in concrete having copper slag as a fine ...


Get More Information

MineralTech CP Copper Slag

MineralTech CP Copper Slag Safety Data Sheet Prepared according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 08/25/2015 MineralTech CP Copper Slag 2/7 First-aid measures after inhalation : IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing. Get


Bacterial corrosion Sulphate reducing bacteria, left undisturbed in marine Also referred to as micro-biological silt or mud deposits, will produce concentrations of corrosion or anaerobic (without oxygen) corrosion, hydrogen sulphide which are particularly aggressive this type of corrosion may occur if local operating to steel and copper based ...


includes fine aggregate of copper slag, with different ratios of water to cement. They concluded that mortar containing a high amount of copper slag sand at w/c= 0.48 had a lower premature strength. Mobasher et al. (1996) investigated the use of copper slag as a cement additive in concrete mixtures during their research phase.


copper slag concrete (M20 Grade) by partially replacing sand with copper slag. The strength was found to maximum at 40% of copper slag replacement with sand. It was also observed that for increased partial replacement of copper slag beyond 40%, the strength of copper slag concrete decreases. A. M. Shende et al. [5] studied the


COPPER SLAG AND GROUND PUMICE ALI BEHNOOD March 2014 ... Chloride-Induced Corrosion of Submerged Concrete Structures in Marine Environment, International Conference on Corrosion and Prevention, Australian Corrosion Association, Brisbane, Australia, 10-13 November, 2013.


partially or completely. Although studies indicate use of Copper slag as aggregate influences the performance of concrete, not much research has been done regarding its use as fine aggregate in SCC. Cooper slag is a by-product in the manufacture of copper. For every ton of copper produced, roughly 3 tons of copper slag gets generated.


Chloride-induced corrosion of steel bar in concrete is one of the main problems affecting the durability of reinforced concrete (RC) structures. Expansive products are formed due to corrosion at the interface between concrete and steel bar. In this study, the differences in the magnitude of the macrocell corrosion current density in RC column specimens cast using copper slag fine …


Copper slag usually has a low content of CaO; granulated copper slag exhibits pozzolanic properties as CaO content in copper slag increases, it can exhibit cementitious properties. Studies [8-12] indicated that a copper slag, which contains approximately 19% CaO, show a good cementitious property under the activation of NaOH.


The addition of upto 50% of copper slag as a sand replacement yielded comparable strength with that of the control mix. However, further additions of copper slag had caused a reduction in the strength due to an increase of the free water content in the mix. Mixes with 80% and copper slag replacement gave the lowest


From the fig.7 it was observed that the copper slag admixed concrete showed higher corrosion rates than normal concrete in various percentages of replacements. The corrosion rate of copper slag admixed concrete increases as percentage of copper slag increases. The corrosion rate can be controlled by coating the bar with Zinc Phosphate paint.


of concrete with copper-slag fine aggregate, with few exceptions [e.g. 236,, 25]. In the former two papers con-crete sand was partially replaced by copper slag and the water absorption, corrosion of reinforcement, chloride per-meability and acid and sulphate resistance of the resulting concrete were studied. It was found that concrete with cop-


4. Copper Slag - Copper slag is a by-product material produced from the process of manufacturing copper. As the copper settles down in the smelter. The end product is a solid, hard material that goes to the crusher for further processing. Copper slag used in this work was bought Ujjwal industries (India) Pvt.ltd, Ahamednagar,


partially replaced with copper slag as percentage ranging 0%, 10%, 20%, 30% & 40% by weight of sand for M25 grade concrete. And tests conducted on hardened concrete is compressive strength test, split tensile test, flexural strength test and sorptivity test after specimens are cured for 7, 28 days curing. ...


Copper slag Copper slag is a byproduct generated from refining of copper and it is also considered as a waste material. For every ton of refined copper, about 2.2 to 2.5 tons of waste slag is produced, which could be used as a replacement material for aggregates in concrete. Thus, copper slag possesses similar properties that of the sand.


Morphology of Corrosion on Excavated Archaeological Metal Artefacts Siatou Amalia*, Lekatou Angeliki Laboratory of Applied Metallurgy, Department of Materials Science and Engineering, University of Ioannina, 45110, Ioannina, Greece [email protected], [email protected] ABSTRACT The present paper is studying the nature and stromatography …


cases slag can be collected as oriented or at least partially oriented (horizontal) samples, allowing directional analysis as well. Frequently, slag traps charcoal fragments from the smelting furnace which would enable radiometric dating by 14C. Hence slag has the possibility of combining the advantages of good performance during the paleointensity


[Jirapure & Borade, 3(7): July, 2014] ISSN: 2277-9655 Scientific Journal Impact Factor: 3.449 (ISRA), Impact Factor: 1.852 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY Naval Corrosion--Causes and Prevention S.C. Jirapure1, A.B. Borade2 1 Assistant Professor, Department Of Mechanical Engineering, JD …


conducted on various corrosion and durability tests on concrete containing copper slag as partial replacement of sand and cement using M20 grade concrete at various proportions of copper slag replacement with sand of 0%, 20%, 40%, and 60%, cement of 0%, 5%, 15% and 20% and combination of both (60% sand + 40% copper slag for fine aggregate and 85%


copper, molten slag containing iron oxides plus gangue and flux oxides, and offgas. The slag typically contains as much as two percent copper. This slag can be recycled to the flash furnace, or its copper content can be recovered in a slag cleaning furnace, often …


Résumé/Abstract Copper slag (CS) and cement by-pass dust (CBPD) are by-products of the production of copper and cement, respectively. In the Sultanate of Oman, large quantities of copper slag (60,000 tons/year) and cement by-pass dust (25,000 tons/year) are produced every year, most of which is not effectively utilized and disposed on-site ...